Our 4WD Cool All Temperature, universal ski and snowboard wax is a great all purpose wax at a great price. Race proven formulas using the highest quality of hydrocarbon waxes. No additives. Available in four temperatures that offer the best value in the industry! Contains no flouro.

• Warm = 32ºF to 28ºF (0ºC to -2ºC)
• Cool = 28ºF to 21ºF (-2ºC to -6ºC)
• Cold = 21ºF to 5ºF (-5ºC to -15ºC)
• Ice Cold = 5ºF to -22ºF (-15ºC to -30ºC)
• Base Prep = Used to clean and protect base 32ºF (0ºC)

Size: 165g

Also sold in smaller 65g bars, 750g bulk bars and 5 pack w/assorted temperatures.

See the complete line of 4WD Waxes

Hot Waxing: Base must be clean & dry. Hot wax your base with the temperature specific wax for best results. Let wax cool completely and scrape with a plastic scraper. Brush out remaining wax from base and polish smooth.

Triangle scrapers offer more sharp edges to use.

Our 6 inch long, clear, ultra thick snowboard wax scraper is made from 1/4" thick high grade acrylic producing a super sharp edge and the extra thick material is heavy duty and has zero flex.  Acrylic is a better material than simple plastic because of the ability to get a sharp edge.  If the edge gets built up with wax or starts to feel dull run it across a steel file or some sand paper to sharpen it back up.  Notched corner allows for easy cleaning of wax off your steel edges. All you need to get the job done.

Size: 3" x 6" x 1/4" thick

Our 12 inch long snowboard wax scraper allows you to cover a lot of ground with each pass.  Made from 1/8" thick high grade acrylic producing a super sharp edge.  Acrylic is a better material than simple plastic because of the ability to get a sharp edge.  If the edge gets built up with wax or starts to feel dull run it across a steel file or some sand paper to sharpen it back up.  Notched corner allows for easy cleaning of wax off your steel edges. All you need to get the job done.

Instructions:

1. Select correct temperature specific wax by checking mountain conditions/snow report...(actual snow temperature, not air).

2. Press wax on the iron and distribute small drips of wax over the entire base. DO NOT ALLOW IRON TO SMOKE!

3. With iron in hand, slowly pull the iron over the wax drips smoothing them into a sheet of wax that covers the entire base tip to tail.

4. Let the wax cool 10-15 minutes, then scrape with a sharp plastic scraper. DO NOT USE a steel scraper.

5. Use a wax brush or fiber pad, remove excess wax from base, brushing from tip to the tail. This allows your base to glide fast. 

Keep your foot where it should be.

We mold and then produce these pads in our Belfair Factory!

Instructions: 

1. Clean board surface and dry completely. Use ONEBALL base cleaner, rubbing alcohol, or another solvent may be needed to get off dirt. Let the solvent dry for 10 minutes. 

2. Mark area where pad will be placed with pencil first. Peel off backing of pad. Place stomp pad in front of your back foot binding and center edge to edge.

3. Only stick once, do not move, making sure not to damage adhesive. Use your fingers to press on pad with firm pressure. Use a hair dryer or heat source to help the pad stick if you want. 

4. Let stomp pad adhere to board for a minimum of 12 hours before using. Better yet, bring your board inside your house and let the stomp pads rest overnight. 

This is a 165g bar of our F1 Graphite Plus. An all temperature hydrocarbon ski and snowboard wax with micronized graphite additive. Fast in all snow conditions but especially excels in cold or dirty snow conditions. Use this universal wax alone or as a mix with any alpine wax for added speed.

Optimal Temperature: 28ºF to 21ºF (-2ºC to -6ºC)

Size: 165g

Hot Waxing: Base must be clean & dry. Hot wax your base with the temperature specific wax for best results. Let wax cool completely and scrape with a plastic scraper. Brush out remaining wax from base and polish smooth.

Rub On: Apply wax to base by hand and cover completely. Use a waxing cork to polish wax into base with firm pressure. A scraper can be used and then use a waxing brush to polish the base...horse hair brush is best for this.